Passive Dehydration System Parts 

3x24-pds-new-rendering.jpgThe PDS, or Passive Dehydration System, is Croft’s preferred alternative to a glycol unit for the dehydration of natural gas. Dehydrating raw natural gas is necessary to remove the water to bring the gas to a point where it is within a range to make it pass pipeline specification usually 7 lbs/MMcf. The PDS utilizes a patented, environmentally-friendly desiccant, enviroDRI™, to dehydrate the gas with minimal moving parts. Wet gas enters the inlet at the bottom of the vessel which allows the gas to rise through the enviroDRI™ and combine through adsorption. Since the enviroDRI is non-hazardous, there are no special disosal instructions.

It is recommended that the PDS be serviced on a 30-day schedule to ensure the system is running properly, as well as the parts. As with any system, there are many parts that can wear down over time.

Passive Dehydration Parts

  • Thermowell, REOTEMP, ST4313-HS

    REOTEMP

    Thermowell, REOTEMP, ST4313-HS

    REOTEMP Threaded Thermowells make it possible to remove an instrument without dropping pressure or losing contents of the process. Thermowells also protect the instrument from getting bent by the process media. Threaded thermowells are perfect...

    $21.53
    Add to Cart
  • Thermowell, REOTEMP ST4316-S

    REOTEMP

    Thermowell, REOTEMP ST4316-S

    REOTEMP Threaded Thermowells make it possible to remove an instrument without dropping pressure or losing contents of the process. Thermowells also protect the instrument from getting bent by the process media. Threaded thermowells are perfect...

    $64.00
    Add to Cart
  • Popoff Vent Cap, NPS, Taylor Valve EPC

    Taylor

    Popoff Vent Cap, NPS, Taylor Valve EPC

    The EPC ensures valve and system protection from environmental elements, enhancing service life and limiting repair costs. The unique lanyard design adds a leak detection capability that sets this product apart from competitors. 

  • EUA3 Low Pressure Control Valve Kimray

    Kimray

    EUA3 Low Pressure Control Valve

      Connection Size: 1 " Connection Type: Female NPT Body Style: Through Body Body Material: Cast Ductile Trim Size: 0.5 " Trim Type: Modified EP Seal Class: Class VI Process Fluid: Liquid and Gas Max...

    $248.42
    This item is temporarily out of stock.
  • 1" x 12" Carbon Steel

    Kimray

    Thermowell

    Lead time: 8 weeks *CALL FOR AVAILABILITY*   Protects the sensing element of the Kimray T-12 Thermostat and allows for the removal of the thermostat without losing vessel pressure. Connection Type: Male NPT 1" x 12" Carbon Steel and Stainless...

  • 1" Kimray Valve. Used as Dump Valve or Pressure Regulator.

    Kimray

    1" HPCV

    1" valve. Used as Dump Valve or Pressure Regulator. The Stem Guided valves have smaller trim sizes for smaller valve coefficients (Cv) compared to the Cage Guided series. "Stem-guided" refers to the stem itself guiding the trim into its seat...

    $635.65
    Choose Options
  • The Kimray 75 PG Pilot is a pressure sensing device designed to output a gas signal based on a set pressure.

    Kimray

    PG75

    The Kimray 75 PG Pilot is a pressure sensing device designed to output a gas signal based on a set pressure. The 75 PG Pilot has a set pressure range of 75-750 PSIG. These pilots are commonly used on control valves to operate them as Backpressure or...

    $1,393.25
    Add to Cart
  • The Kimray Back Pressure valve controls pressure upstream of the valve by adjusting the set point to the desired max upstream pressure.

    Kimray

    (230 SGT BP-D) Backpressure Valve, AAR

    The Kimray Back Pressure valve controls pressure upstream of the valve by adjusting the set point to the desired max upstream pressure. Used on separators, flow treaters, compressor stations, and gas gathering systems. Utilizes process gas to operate...

    $806.39
    Add to Cart